Flaming-river Keyless Ignition Systems Manual de usuario descargar pdf

INSTALLATION INSTRUCTIONS PUSH BUTTON START SYSTEM

SYSTEM OVERVIEW

The PUSH BUTTON START SYSTEM supplements a standard automotive ignition switch with

a radio controlled secure start system. The driver is able to control the ACC, IGN, and STR

functions by use of an illuminated push button.

The system is designed to be wired in parallel to the existing ignition switch.

The switching functions of the ignition switch, which in a standard automotive system are

used to switch battery power to accessory, ignition, and starter circuits, are replaced by

3 relays controlled by the PUSH BUTTON START SYSTEM. The individual relays are used to

provide the system power to the accessory, ignition, and starter circuits.

CONTENTS:

Near Reader Module

Push Button Switch

FLAMING RIVER INDUSTRIES, INC

800 POERTNER DRIVE

BEREA, OHIO 44017

800.648.8022

INSTALLATION - WIRING OVERVIEW

Instruction Sheet

Main Were Harness

Remote Keyless Entry (RKE) System

PART NUMBER FR60003

Before beginning the installation, please review the most recent instructions at:

http://aftermarket.strattec.com. For questions concerning installation or performance,

please call 1-800-648-8022.

Revised 7/28/10

Notes to the Installer:

1. If this is the ﬁrst time you have installed the FLAMING RIVER PUSH BUTTON START SYSTEM into a vehicle, it is recommended that the complete system should be temporarily

powered up and tested outside of the vehicle prior to ﬁnal installation and hard wiring into the vehicle. Either a standard 12 volt battery or a 12 VDC power supply is adequate to

power the system. Fuses should be inserted as needed into the supply circuit. This bench-top testing of the system will allow the installer to become familiar with the operation of

the system as well as the wiring, fusing, and load requirements.

2. Follow good automotive wiring practice for installation of the system.

3. All wires on the switch harness, main harness, and relay harness are printed to show the connection to/from information. In addition, a wire chart is included in the instructions to

show the wiring information.

4. The system uses the Deutsch DTM type connectors for connection to the main and antenna harnesses. All connectors are keyed with different unique housing conﬁgurations. The

Deutsch connectors may be disconnected and reconnected as needed to route the harness and antenna wires as needed. Do not remove the individual wires from the Deutsch

housing shells unless the wires are damaged and require repair.

Docking Station

Relays

Docking Station Face Plate

Docking Station Mounting Hardware

Relay Harness

FOB

Push Button Switch Harness

INSTALLATION INSTRUCTIONS PUSH BUTTON START SYSTEM

SYSTEM OVERVIEW

CONTENTS:

INSTALLATION - WIRING OVERVIEW

1 2 3 4 5 6 ... 10 11

Indice de contenidos

Pagina 1 - CONTENTS:

1INSTALLATION INSTRUCTIONS PUSH BUTTON START SYSTEMSYSTEM OVERVIEWThe PUSH BUTTON START SYSTEM supplements a standard automotive ignition switch with

Pagina 2 - Figure 1

10112. CONTROL WIRE WIRING ILLUSTRATION CAUTIONS: 1. Connect – Red wire and Black wire to battery Cathode and Anode respectively.

Pagina 3 - Figure 2

10114. TROUBLESHOOTINGCONDITION RESOLUTION RECOMMENDED1. Neither the main-control lock nor sub-control lock functions. A. Check the connection of powe

Pagina 4 - Relay Pinouts

232. Locate and identify the circuit terminals on the back of the ignition switch assembly. ACC – Accessory Terminal IGN – Ignition Terminal ST –

Pagina 5 - STEP 10 - FOB REMOVAL

23STEP 51. Mount and position in a convenient orientation the three (3) relay pack assembly to a ﬂat surface.STEP 31. Mount the Docking Station in d

Pagina 6

45STEP 6Relay pack wiring (please refer to the relay pack wiring diagram). 1. Operation: The system uses standard automotive rated Form C relays to

Pagina 7

45STEP 8 - VERIFY PUSH BUTTON START SYSTEM OPERATION:1. Ensure the FOB is located within the docking station.2. Pressing the push button switch for

Pagina 8

67RELAY HARNESS WIRE TABLERELAY BLOCK LABELRELAY PIN WIRE COLOR GAUGE AND INSULATION WIRE MARKING FINAL CONNECTION TO NOTEACC RLY 30 RED 12 GXL ACC

Pagina 9

67Central Locking System User’s ManualFunctions1. Arm Press button on the FOB, the doors will lock automatically and the engine will be immobil

Pagina 10 - .1. .2. .3

89Installation Instruction For Remote Keyless Entry (RKE) SystemA. COMPONENTS & PARTS ILLUSTRATIONS:Components & Parts Speciﬁcation ListModel

Pagina 11

89 Cautions: 1. The installation of the Control Lock shall never obscure the mechanism and motion of car door and glass. 2. Make s

Comentarios a estos manuales

Sin comentarios

Flaming-river Keyless Ignition Systems Manual de usuario

Busca en linea o descarga Manual de usuario para Hardware Flaming-river Keyless Ignition Systems. Flaming River Keyless Ignition Systems User Manual [it] Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Flaming-river Keyless Ignition Systems